Replacing the Head Gasket

WITH PICTURE 

Starting Procedures:

• Open Hood.
• Disconnect the battery.
• Drain coolant.
• Remove airbox assembly - unbolt from rear of head.
• Unplug wiring harness and strap it out of the way.
• Remove the coil pack and wires.
• Remove ground strap from head.
• loosen and disconnect EGR valve from head. Actual removal from
  engine bay unnecessary.
• Unbolt intake manifold from head.
• Remove spark plugs from head.
• Unhook Fuel Injection Assembly from fuel line.
• Remove Fuel Injection rail/fuel injectors from head. Note:
  Was informed, not a necessary step
• Remove alternator belt.
• Remove valve cover.
• Unbolt exhaust from exhaust manifold. [Beth Boose wrote: "do not
  unbolt exhaust from head- after everything else is removed, place a
  jack (with a block of wood on top) beneath the catalytic converter and
  slowly jack the cat up, this will pop head free- no need to pry the
  head up. Then unbolt the exhaust from the cat - it's easier to remove
  the exhaust bolts with the head off the car.]

I might have left a few things out, but you basically remove
everything and kep track of where it all goes. I take pictures. I have
a digital camera, but a Polaroid will do.

Now we start getting to the fun part:

• Jack the right side of car til the tire is off the ground and
  support it.
• Remove the front tire.
• If you replaced the engine cover, remove it again.
• Loosen air conditioning compressor, then remove belt.
• Remove power steering pump/belt if applicabe.
• Remove crank bolt.
• Using the puller, remove the crank damper/pulley.
  • Removing this can be a real pain. Fortunately for me, mine came
    off easily. We had one that was very difficult at first. We actually
    broke one pulley. We then spayed it heavily with some PB Blast (there
    are other penetrating oils available) and let it sit overnight.
    Probably wouldn't hurt to hit the crank damper/pulley with a rubber
    mallet to help the oil penetrate. Other people have used a torch to
    heat up the pulley. There is a puller specific for the Chrysler
    2.0/2.4. This
    is the one SnapOn sells.
• Remove front timing belt cover.
• Place floor jack with wooden block under the oil pan. Raise jack
  til block touches the pan. You can use the floorjack to raise/lower
  motor to help with clearances.
• Unbolt/remove engine mount.
• Rotate the crank until the timing marks on the gears line up with
  the cover.
• Remove tensioner.
• Remove timing belt.
• remove timing gear from head/camshaft.
• Remove rear timing cover - if you plan on changing the water
  pump.

Now, since so far, we have done all the procedures to remove a
timing belt, it would make sense to use a new belt, so we don't have to
do the labor twice when unnecessary. The timing belt's recommended
change interval is 105,000 miles. I changed mine at 127,000 miles when
I did my head gasket.

On another note, you have to go through these procedures to get to
the water pump. Usually, they would charge another 1/2 hour labor to do
the change the water pump. A water pump's life expectancy is not much
greater than 100,000 miles.

Some say you should remove the cam from the head. If you want to
examine the cam lobes and actuators, you can remove the cam. I didn't
when I did mine. If you have a DOHC motor, you need to remove the cams
to have adequate clearance to reach and remove the headbolts.

• Remove thermostat housing.
• Remove headbolts.
• Loosen the head from the block by rocking and careful use of a
  prybar.
• Lift the head with the exhaust manifold and remove from the car.
• Clean all surfaces - block, head, intake ports.
• Check surfaces for warpage - check specs in service manual.

The assembly is pretty much the reverse of disassembly. A few notes:

• Use new head bolts if you are worried or the originals are
  stretched. (Some people recommend simply always using new head
  bolts since they do not cost very much.)
• Make sure you tighten the bolts to specs in the correct order.
  Refer to the manual.
• Replace the rubber grommets in the valve cover.
• Replace the tensioner with a new one. It might not be necessary.
  I have 170k miles on mine. But a friend of mine, his Breeze's tensioner
  broke about 3k miles after his headgasket replacement. So, you might
  want to be safe than sorry. (Editor's note: if you use the old one,
  make sure you reset it.)

View of front of motor with crank damper:

 

View of motor front with the front motor mount removed:

View of front of motor without crank damper and rear timing cover:

View of enginebay with the valve cover off:

View of motor from top. if you look where the orange stuff is, this
is where the 2.0/2.4L motors tend to pour oil:

View of motor from top with the MLS gasket:

View of head removed from car. Notice the rust stains in the
combustion chamber. This is due to the coolant leaking into the piston
  area: